A bass note does not always end when the instrument stops. In a small room, the walls can make some low notes swell in one place, vanish a few feet away, then linger after the music has moved on. That lingering response is the problem Dirac’s Active Room Treatment (ART) is designed to address—not simply a shortage of bass. The idea is to coordinate the speakers already in a system so they can shape how low-frequency energy behaves across a listening area.
Dirac is a Swedish audio-software company founded in Uppsala in 2001 by six researchers. In a 2017 interview, co-founder Mathias Johansson recalled their work on optimizing loudspeakers’ frequency and impulse responses; he said the company name refers to the idealized Dirac impulse, an infinitely brief signal used to describe a system’s transient response. ART applies the same broad interest in time and sound to a different scale: not just the loudspeaker, but the loudspeaker–room system. That is a useful thread through its history, not a claim that ART is the same algorithm as the company’s first products.[1]
ART arrived in Dirac Live Processor for PC and Mac on 30 June 2026, adding a computer-based route alongside compatible receivers and processors. The more important story is not the launch itself. It is what changes when room correction stops treating each speaker as an isolated source and starts treating their positions as resources.[3]
When the room keeps playing
Low frequencies have long wavelengths, and room boundaries make them interact in patterns called room modes. Think of a five-metre room dimension: using the usual speed of sound, its first length mode falls at roughly 34 Hz, with higher modes around 69 and 103 Hz. These are illustrative calculations, not a measurement of any one home; Dirac’s own stereo guidance gives a similar 35/70/105 Hz example.[8]
A mode is not a single “bad frequency” floating evenly through a room. It creates a pressure pattern: a listener near one wall may hear a strong peak while someone nearer a node hears a dip. The same energy can decay differently at different places. An organ note or the tail of a kick drum may therefore feel woolly or overhang one seat, but comparatively lean at another. What is heard as “too much bass” can be a mismatch in level; what is heard as bass that will not get out of the way is partly a time problem.
Equalization still matters. A filter changes the signal’s phase and impulse response as well as its frequency magnitude; it is inaccurate to say that ordinary room correction “does nothing in the time domain.” Dirac’s own description of Room Correction includes frequency and impulse-response correction. But the conventional correction problem is narrower: the speaker channels are optimized individually over a measured region. It cannot make a deep cancellation at a particular seat disappear simply by turning up that same source—the reflected wave rises too, and the boost can consume amplifier and driver headroom. Moving a speaker or seat, or adding another source in a different position, changes the acoustic problem itself.[2]
That distinction helps place ART in context. Its 20–150 Hz working region is where room modes commonly make bass uneven and slow to settle. ART is not a universal promise that every bass note will stop instantly; it is an attempt to better control the combined response in the area that was actually measured.[5]
Room Correction, Bass Control and ART solve different parts of the chain
It is easiest to understand Dirac Live as a progression of related jobs, not three competing labels. Room Correction adapts each speaker’s frequency and timing response to the room. It can improve the average response across several microphone positions, but a particular seat may still differ from that average. It is useful even in a system without a subwoofer, and it can change measured impulse response; the point is that it does not give all speakers a shared low-frequency task.[2]
Bass Control addresses the handoff between main speakers and one or more subwoofers. It measures how those sources combine, then adjusts timing, level, and bass distribution so their crossover region works more evenly across listening positions. With two subwoofers, for example, it can use their different locations to reduce seat-to-seat variation. That is more than “turn the subs up”; it is bass management and spatial integration. But its job is still centered on integrating the subwoofer system with the main speakers.[4]
ART builds on Room Correction by allowing other capable speakers—not only subwoofers—to support each main speaker group in the bass region. Dirac describes this as a multiple-input, multiple-output (MIMO) system. Its technical paper explains the practical difference: for each speaker, conventional single-input correction uses that speaker’s measured impulse responses; ART’s calculations use the set of responses linking the system’s speakers and microphone positions to design both primary and support filters. The filters are optimized together toward a desired impulse response and average target curve across the measured area.[2]
In plain terms, two sources in different positions give the processor more ways to influence the same room mode than one source does. ART is not merely a more aggressive bass EQ, nor should it be reduced to a simple “anti-noise” speaker. It is a coordinated filter design with a bounded bandwidth, defined main and support groups, and trade-offs between how tightly the result is optimized and how much of the room it covers. It is an add-on to Dirac Live Room Correction; a system configured with one or more subwoofers also requires Bass Control. [5][6]

Support is a real speaker doing real work
In ART’s setup, each “main” group is the channel or set of channels whose response is being optimized; other groups can be designated as support. The guide allows a support range to be constrained below and above. The lower limit helps keep a small satellite from being asked to produce bass it cannot handle. The upper limit matters because a nearby surround may become audible as a separate source if asked to help too high in frequency. The limits are not cosmetic sliders: they encode what a speaker can do, where it sits, and how close a listener is to it.[6]
The guide treats support level as a way to balance use and avoid distortion. More speakers are not automatically better: a floorstander, compact ceiling speaker, and subwoofer do not share the same bass extension or output margin. ART can only use what the system can deliver. If a supporting channel strains, reduce its contribution, raise its low-frequency cutoff, or stop assigning it to that task. Available speaker and amplifier headroom is a design condition, not an afterthought.[6][7]
The measured region matters just as much. Dirac’s ART guidelines warn that too few microphone positions can overfit the correction to a few spots and leave uncontrolled behaviour between them. Its general recommendation is at least nine positions for most setups; the exact number and pattern depend on the room, number of active support speakers, and size of the listening area. A narrower zone may allow a more precise result, while a large sofa or open-plan room asks the correction to cover a harder, less uniform space. More support speakers can help within a fixed area, but they can also create unexpected behaviour outside the measured area if the measurements are sparse.[9]
Two speakers, two subs, or a cinema array
A stereo 2.0 system is not excluded. Dirac says two bass-capable main speakers can support one another, but it gives a low-frequency cutoff of 70 Hz or below as a practical minimum, and the room modes must fall in the speakers’ useful range. In the illustrative five-metre room, a pair that barely reaches 70 Hz may have little ability to address the 34 Hz fundamental; it could still interact with the next mode around 69 Hz. If the speakers roll off well above the bass problem, ART may have little to work with, and ordinary Room Correction may be the more proportionate tool.[8]
A 2.2 setup changes the geometry. Two independently addressable subwoofers provide additional sources at positions that may excite the room differently from the left and right speakers. With Dirac Live Processor, a stereo input remains stereo, but two mains plus two subs require four physical output channels; the computer, DAC/interface, and playback routing must actually expose them. A two-output DAC does not become a 2.2 system because a software licence says ART. Dirac’s processor supports up to eight speaker outputs for stereo input, including the two main channels and up to six subwoofers, but the usable limit is also determined by the hardware and routing available to you.[10]
In a home cinema, the potential support network is larger: fronts, centre, surrounds, height channels, and subwoofers may contribute according to the device’s layout and ART group settings. A film’s channel map remains the starting point, but the room correction can coordinate capable groups to shape their low-frequency behaviour together. The point is not to have every speaker reproduce deep bass. It is to choose which sources can usefully assist which main groups, at what frequencies, without compromising the speaker’s normal role. The PC routing tutorial gives a concrete 5.1 example: choose 5.1 as the incoming soundtrack format, then add two separately routed subs to make a 5.3 output system. That means five main channels plus three subwoofer outputs; it does not remix the movie into new content channels. The processor can then calculate the room correction for the speakers and subs connected to those outputs.[10] A 2023 StereoNET interview with Dirac’s then Head of Product, Nilo Casimiro, made the trade-off plain: a broad seating area has more different impulse responses to reconcile, so the algorithm must compromise. That is a developer’s description, not independent verification, but it is a useful correction to any “every seat” promise.[16]
The computer route makes routing visible: DLP processes PC/Mac audio before it reaches the system. If a TV app sends sound directly to an AVR, it bypasses DLP; if the computer is the source, its operating system must send audio through the virtual device and out to the correct physical channels. A receiver with ART built in uses its own AVR signal path. In 2025 Dirac announced ART for selected Denon and Marantz models that already supported Room Correction and Bass Control, a reminder to check the exact model and licence path. [12] PC users also need enough CPU headroom: Dirac labels its 16-channel full-support benchmark a worst case and recommends trying the intended setup under a normal workload rather than treating a CPU figure as a guarantee.[3][11]
What would count as evidence?
A flat frequency-response graph can show that bass levels are more even, but it cannot on its own establish that a long resonance has shortened. To assess a claim about decay, inspect a time-based view such as a waterfall or spectrogram, and compare the original, Room Correction, Bass Control, and ART under the same conditions. REW’s waterfall guide explains that each slice comes from a windowed portion of an impulse response; the window width and settings affect what appears. Different smoothing, time range, or frequency resolution can make two plots look more different—or more similar—than the underlying measurements justify.[13]
An Audioholics review from 2025 offers a measured example, not a universal benchmark. Its author tested Focal 1000 Utopia speakers with a Focal Astral 16 processor and several subwoofers in his own treated reference theatre. He manually assigned support groups, worked with Dirac and StormAudio engineers, and says he left ample headroom for each group. At the reference seat, a REW plot with 1/24-octave smoothing showed a near-flat LFE response from about 20 to 120 Hz. That graph demonstrates a smooth level response in one powerful system; it does not by itself show how quickly a resonance decays, and it is not a blind listening test or independent-lab trial.[15]
A separate REW check published by Heimkinobau in 2026 uses the company’s own StormAudio demo cinema, with 23 speakers and nine widely distributed subwoofers. At one reference seat, its post-ART LFE spectrogram showed residual energy at 20–30 Hz; the article reports decay times of roughly 0.13–0.15 seconds around 100 Hz. This is a readout of the room after calibration, not a measured reduction: the cited section has no before-and-after series or seat-to-seat sweep. The two reports answer different questions—one shows level smoothness, the other describes remaining decay—so neither can stand in for a controlled, multi-seat comparison. To compare fairly, hold playback level, target curve, microphone positions and graph settings constant, save the uncorrected baseline, and check more than the “best” seat.[17]

What the algorithm cannot move
ART’s promise is specific: help a capable loudspeaker system manage low-frequency room behaviour across a measured listening zone. It does not fix rattling doors, stop sound escaping through a wall, correct every reflection above its working band, or change the geometry that created a deep null. Placement still matters; moving a subwoofer or seat can change which modes are excited or heard. Physical absorbers and structural isolation do different jobs. Genelec’s room-acoustics guidance notes that thick absorbers are needed to affect low frequencies and that calibration alone may not resolve every acoustic problem.[14]

That is why ART’s most persuasive use case is neither “replace the room” nor “add bass.” It is a room whose low end is measurably uneven or slow, a speaker layout with enough capable and addressable sources to give the processor options, and a listener willing to measure across the seats that matter. If the system lacks outputs, bass extension, or headroom, the software cannot supply those missing resources. The worthwhile question is not whether a graph can be made prettier, but whether a specific room’s bass settles more consistently without pushing its speakers beyond what they can do.
Research checked 2 November 2026. Manufacturer documentation, the developer interview and room-specific measurements are identified in the sources.